Dutchman/Boom Lift
Dave Peffer
11/1/1997
Hull #: 20
Earlier hull numbers have an adjustable two-part boom lift designed to permit setting up the Dutchman exactly. This has a nasty tendency to shake out of the cam cleat at the end of the boom, and re-setting it with the sail luffing is no picnic. I opted to set the system up perfectly, then whipped the two parts of the boom lift together just above the cam cleat. No more loose line and the whipping can easily be cut when necessary.
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Many of us have noticed that the Catalina 380 fridge needed a bit more insulation to make it effective. The factory fix has been appreciated and worthwhile. I also felt that the placement of the compressor is in a rather vulnerable position in the bottom of the port lazarette. Objects could be dropped on it or it could (and would) be stepped on.
On Samantha we moved the compressor to a shelf glassed into the area between the port propane locker and the hull. This required new copper plumbing and a refrigerant recharge, but there was plenty of unused space. Now it is safely out of the way and still easily accessible. To make certain that it has adequate ventilation we installed a stainless vent between this area and the aft cabin, which is probably a good idea whether the compressor is
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Having the GPS mounted on the pedestal is convenient, especially if you have a 12V outlet to power it so you can keep the light on at night. There is not an outlet provided, so I added one. Using a Marinco 12VRC outlet with a rubber cover and a good seal, I placed it on the lower port quadrant on the side of the engine instrument pod, where it would be angled downward to prevent water running down into the barrel of the outlet or around the edge, should the seal fail. Be sure to check for interference with instruments inside the pod before drilling. Inside the pod is a connector block, and I was able to add the wires to appropriate slots on the block without crowding. Caution: the wiring is not heavy enough to support using the outlet for
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
I finally got my problem solved. When we ordered our new C380, we ordered it with a Garmin 215 GPS with Differential built in. Well, the GPS worked fine but no differential. The dealer and the West Marine rep tried everything but still no workie. (I forgot to tell you I also had a inverter installed as well) By luck the rigger who was working on my boat turned off the inverter and lo and behold the differential started to work. So, after rewiring, trying a new GPS and new antennas, it was just interference from the inverter. So, I do not use the inverter when under way.
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
A swing-down white plastic tray/drawer that mounts easily under the medicine cabinet to hold small items such as milady’s makeup, wallet and change, car keys and whatever. It has positive detents in the up and down position. It is available from ABC, Inc, 1-800-877-4797
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Head Lid and Seat Support
Dave Peffer 10/1/1998
Hull #: 20
The earlier hull numbers were designed without support for the lid and seat in the raised position, which means the hinges break. I made a “T” support of teak, which is screwed into the bulkhead behind the head. Since the bulkhead does not line up with the hinge axis, the “T” is angled 8 degrees to provide a direct 90-degree support for the lid. A rubber tip protects the lid. Looks OK, works fine.
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Who wants to climb down into the lazarette to fetch stored items? Why not hang them up in easy reach? We were going to install athwartships stringers under the seat hatch hinges to install hooks but found stainless line hangers at West Marine (model # 243834). These install on the bolts holding the helmsman’s seat supports without any modification, at all, and the hooks are full half-circles. Nothing can fall off even in a full spinnaker broach. We have the emergency tiller and access-plate wrench, a boat hook, spare lines and fenders, a loud-hailer, the windshield and a bag for the dinghy oars on these. A boarding ladder and bucket are fitted with light retrieving lines, which are also hung on these hooks for easy retrieval. The PFD bags sold by marine stores fit snugly through the lazarette hatches, and we keep
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
We all have automatic bilge pumps, but how many times have we actually operated our manual pumps? The location of the pump handle is critical, especially if the crew must pump for extended periods. This operation should have a minimal impact on the helm. And the pump itself was quite an obstacle to entrance into the port lazarette. The solution was to relocate the pump to an area immediately aft of the port propane locker. It is a squeeze, but it fits in an area not otherwise useable. One of the existing hoses had to be replaced. The old pump opening in the cockpit was filled with the piece removed from the new position, glassed in and properly finished by a glass expert. One could never see the original installation! The result is much easier lazarette access, and the operating position
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Mast and Shroud Grounding
Jim Jaeschke 9/1/1998
Hull #: 73
For those of you who did not order the bonding package, here is one idea as to a way to ground the base of the mast and the shroud wires to the keel. There is of course no method in which protection from lightning can be guaranteed. Indeed, there is much debate as to the way that will provide the most protection.
On Electra, we decided to ground (connect) as much of the metal in the boat as possible to the keel. On the lower part of the keel, I have mounted, drilled and tapped, four small Dyna-Plates to make as good an electrical connection to the water as possible. In fresh water, this connection to the water is the weakest link in the protection system. Spread the Dyna-Plates out on the keel on both sides so that the electricity
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
