There are a number of threads dealing with heat exchanger problems. Here is an unusual one from Dauphine, C380 #160:
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
There is a spare parts kit available for the Westerbeke B 42B:
https://www.westerbeke.com/Product/SPAREPARTSKITB42BFOUR/044856?productname=SPAREPARTSKITB42BFOUR&productid=542029E9DAF73B1CA82D7B30
Part Number
Description
Quantity
Unit
011885
ZINC 1/4NPT x 1-3/4
2
EA
017263
FORM, DISTRIBUTOR LISTING
1
EA
022851
GASKET, EXCHANGER 2-3/4 IN
1
EA
024353
GLOWPLUG 12VDC
1
EA
030200
ELEMENT, FUEL FILTER
1
EA
030475
BELT, FAN 39.5 x O
1
EA
030538
INJECTOR
1
EA
030548
ELEMENT, FUEL LIFT PUMP FILTER
1
EA
033093
KIT, HARDWARE W13-33/35B-42B
1
EA
035299
BELT, COG 41.4 X O
1
EA
035450
FORM, SPARES & ACCESSORIES
1
EA
035828
FILTER, OIL
1
EA
041658
BOX, SPARE PARTS KIT
1
EA
043612
THERMOSTAT 160F
1
EA
044855
GASKET SET, COMPLETE 42B FOUR
1
EA
048076
FILTER, FUEL 80 MICRON
1
EA
048500
IMPELLER KIT
1
EA
049000
KIT, WATER PUMP
1
EA
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Several members asked about expected fuel consumption on a C380. The responses were pretty consistent:
It’s going to vary a bit depending on your prop set up and sea conditions. My typical fuel consumption is better than on the chart Rich shared. It is a matter of RPMs and the sweet spot for consumption versus boat speed for my boat is in the 2200-2500 RPM range. I typically burn ~ .75 gallons per hour in that range and can make 6+knots.
Mike
Morning Glory
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Check it out:
Yanmar_PROP_TABLE_GM_and_3JH_series
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Directive from Yanmar regarding recommended antifreeze for their diesel engines:
Yanmar_Coolant (1)
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Note that this is for the 3JH3E (and 4JH3E) engines:
Yanmar_Service_Manual_3JH3E_4JH3E
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Note that this is 3JH3E. At least from 2005, Catalina used the 3JH4E.
Yanmar_Drawings_Parts_List_3JH3-e
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Check out the link below….
Yanmar_JH_Engine_Power_Curves
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
I have a 2002 Catalina 380. There is too much play in the transmission clutch cable, and I have decided to replace it. Does anyone know the length/specifications of the cable for the Catalina 380?
The 3 phase charger installed in the starboard stern hatch no longer works.
Has anyone had to replace this electronic part ?
raykovacs7@gmail.com
Posts navigation
Greatest boats on the water…