Have an old teak pedestal table in the garage? I took mine apart: the ”four-holer”, which attached to the Edson pedestal guard with a stainless strap curved at both ends, fits our pedestal, too. Slide it down until it rests on the instrument pod and you have a great place for drinks, binoculars, a horn, gloves and whatever. Add rubber holders on each side for a hand-held VHF and a cell phone. Add a “Holdz-it” on one side for the GPS.
How about a holder for the bell? We added a brass eye for a small nautical kerosene lamp, nice for romantic dinners. When we’re securing the boat the four-holer comes right off and hangs on one of the hooks in the lazarette.
This is wonderful!
Now you’ve got a teak table top, perhaps with folding leaves. Lose
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Dock Side Water Connection
Dave Peffer
7/1/1998
Hull #: 20
A few weeks ago we were asked by the Coast Guard to display a life jacket for each passenger, requiring us to take one of the PFD bags out of the lazarette. The gal who put it back in didn’t see that sneaky blue tube, and hung up the bag on it, then pushed extra hard. Result: the right-angle fitting from the regulator cracked. When we fired up the fresh water to do dishes the pump ran on and on, but we had no pressure. It took awhile to find this blasted leak!
I have temporarily plugged the end of the tube after removing the fittings, but have to replace the thing if I ever want to use the dockside connection for water. Those who have not (yet) broken it can avoid the problem by disconnecting the blue tube, turning
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
After good meals, a key factor in crew comfort is adequate cabin heat. What a treat a warm cabin is after a cold watch…and how nice it is to be able to dry clothes at sea! We have had experience with diesel heaters before in our Catalina 42 and friends’ boats. They are very economical to run (about 0.5 liters per hour), are quiet/safe in operation, and offer loads of nice hot air.
An Eberspacher Model D3LC was chosen for its heat output and reputation for quality. They are readily available in the USA through selected dealers.
This model was designed for a slightly smaller boat, but installation space and other factors must be considered. Finding a way to mount the heater, locate the exhaust, and run the heat output required careful planning. After much thought, we settled on mounting the main
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Dock Line Storage
Jim Jaeschke
5/1/1998
Hull #: 73
We made a locker for storing dock lines by removing the starboard holder for the spare propane tank. This opened up a large spot for dock lines in the unusable spot underneath the deck. If you do this, it is important to seal this area off since water can pour into the boat. We did this by fiber glassing in plywood walls to totally seal off the interior of the boat. The drain hose used for the spare propane tank locker was then fitted to this new compartment.
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Spare Propane Locker Becomes Cockpit Cooler
Dave Peffer
11/1/1998
Hull #: 20
We rarely need two propane bottles aboard, and we don’t want to open our refrigerator more often than absolutely necessary. My solution was to line the outside of the spare (starboard) propane locker with insulation, working from below in the lazarette. I used three wraps of roll insulation (from a home store) which sandwiches bubble-wrap between layers of foil, lightly gluing it and wrapping it in place with nylon strapping. The bottom was covered with expanded foam insulation board, and the joints sealed withlatex expanding foam insulation (Find this stuff! It cleans up with water!).
The locker cover was lined with the same rigid board insulation. Here I cut one piece to fit inside the water-exclusion fiddle, another to extend down just into the round part of the locker, using contact cement to hold them in place on
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
The anchor locker provides no place to install a chain lock, which is required to keep the anchor locked on the roller underway. I made one up as follows: a short length of 3/16″ stainless wire (length depends on the length of your anchor stock) with a lifeline pelican hook (West Marine model #543132, which adjusts in length) swaged on one end, a stainless thimble nice-pressed on the other. A galvanized shackle attaches this to the bitter-end padeye in the anchor locker. The pelican hook goes through a chain link as close as possible to the anchor, and the adjustment on the hook allows this to be snug. The anchor is not going to fall overboard. This can also be used to snub the chain and allow you to transition the chain to the gypsy while raising the anchor if you do
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Gotta have them. Even the red light over the galley hurts night vision from the cockpit. We added two night lights: one in the head next to and six inches above the seat of the commode below the sink, and one on the curve at the aft end of the starboard settee just above the cabin sole and just inboard of the navigator’s chair hinge support. When installing the latter be sure to remove the settee cushion base (only six or eight screws hold it down) to find the right spot for the light and to avoid drilling a hole in the holding tank, which fits snugly into this corner! You will find a simple electrician’s snake invaluable in such electrical installations. For some reason these lights are hard to find, but I got some from M&E Marine. You may have
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Condensation in the Refrigerator
Jim Jaeschke
9/1/1998
Hull #: 73
On Electra we started noticing in our second season a lot of condensation on the tops of cans in the top part of the refrigerator and also on the top of the refrigerator itself. We performed the dollar bill test which is closing the top cover of the refrigerator with a dollar bill located between the cover and the rubber seal. We found that the dollar bill pulled out easily in several locations along the perimeter which showed that the rubber seal was not touching the top. It was probably compressed from my putting a heavy tool box on the counter. A new one was installed.
I also checked, as suggested by other owners, the junction of the counter top and the top of the refrigerator. I found as they had, a gap that could leak air. I sealed the
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
